The hazards of liquid water in compressed air
The liquid water present in all compressed air systems causes
pipeline corrosion, permanent damage to valves, cylinders,
pneumatic tools and machinery, and reduces the efficiency of the
aftercooler/heat exchanger.
By installing the YUKA WS series of high-efficiency compressed
water separators, more than 99% of the liquid water can be removed
easily and economically.
Your compressed air system will reduce downtime and maintenance
costs, so it will operate more efficiently. The WS high-efficiency
water compressor separator will also improve the efficiency of
downstream equipment such as aftercoolers, refrigeration dryers,
filters, etc., delay the equipment life cycle and save costs.
Working principle
A large amount of water-containing steam enters the steam-water
separator and moves downward in a centrifugal manner.The entrained
water is separated due to the decrease in speed; the separated
liquid flows through the trap and is discharged, and the dry and
clean steam is discharged from the gas water separator outlet is
discharged.
Where Refrigerated Water Separator be installed among the
compressed system?
The Moisture Separator is used in a compressed air system , located after the
water-cooled chiller to separate moisture from the compressed and
refrigerated air and after its exit, the air passes through an air
dryer containing molecular sieve and activated alumina.
Feature & Benefit
A. High liquid removal efficiencies at all flow conditions
B. Protects coalescing filters from bulk liquid contamination.
C. Helps provide air quality in accordance with ISO 8573-1:2001 the
international
standard for compressed air quality
D. Suitable for all compressed air applications
E. Suitable for all compressor types, including variable flow
F. Low pressure losses for low operational costs
G. Low lifetime costs
H. All FWS water separators are covered by a 15 year housing
guarantee.
Technical Specification
The flow rate below is the treatment capacity of compressed air
under rated working pressure 7 barg (100psi g). For the application
in other working pressure, please refer to the correction factors.
| Model | Pipe size | Flow rates | Dimension (mm) |
| L/S | m³/min | scfm | W(Width) | D(Depth) | H(Height) |
| WS 15 | RC1/2" | 40.0 | 2.4 | 84.5 | 89 | 79 | 228 |
| WS 25 | RC3/4" | 60.0 | 3.6 | 127.1 | 89 | 79 | 228 |
| WS 50 | RC1" | 75.0 | 4.5 | 158.9 | 89 | 79 | 263 |
| WS 75 | RC1" | 125.0 | 7.5 | 264.8 | 120 | 110 | 335 |
| WS 100 | RC1-1/2" | 166.7 | 10.0 | 353.1 | 120 | 110 | 335 |
| WS 200 | RC2" | 300.1 | 18.0 | 635.6 | 164 | 151 | 564 |
| WS 250 | RC2-1/2" | 416.8 | 25.0 | 882.8 | 164 | 151 | 664 |
| WS 700 | RC2-1/2" | 700.0 | 42.0 | 1483.1 | 200 | 189 | 712 |
| WS 800 | RC3" | 833.5 | 50.0 | 1765.6 | 200 | 189 | 712 |
| WS 800F | DN80/DN100 | 833.5 | 50.0 | 1765.6 | 280 | 189 | 734/744 |
| WS 1000F | DN100/DN125 | 1000.2 | 60.0 | 2118.7 | 280 | 189 | 780/795 |
| WS 1200F | DN100/DN125 | 1166.7 | 70.0 | 2464.0 | 280 | 189 | 1058/1073 |
| Technical requirements | Maximum operating pressure: 10 barg Operating temperature:1.5~ 80°C |
| Pressure | Barg | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 |
| Psig | 15 | 29 | 44 | 59 | 73 | 87 | 100 | 116 | 131 | 145 | 160 | 174 | 189 | 203 | 219 | 232 |
| Correction factor | 0.38 | 0.53 | 0.65 | 0.76 | 0.85 | 0.93 | 1.00 | 1.07 | 1.13 | 1.19 | 1.23 | 1.31 | 1.36 | 1.41 | 1.46 | 1.51 |
Success Cases
